Drag out the machine very carfully. Don't force it if it doesn't move. Check the incoming water hose/connection hose that it is not tangled.

Stretch out the connection hose and very carfully push the machine back in place. Don't push the machine all the way back into the wall.

Happens when equipment is not cleaned properly. Drainage-pipe is attached under the sink NO3 with a hose clamp.

Unscrew the hose clamp with screwdriver. Pull of the drainage-pipe with your hand carefully.

Open the hatch for the dishwasher and pull out the waterplugg. Shut off the machine.(No need to turn of fusebox or incoming water).

Blow into the drainage-pipe hard until you can see/hear waterbubbles inside of the dishwasher. Repeat 3-5 times to make sure nothing else is stuck.

Reattach the drainage-pipe with the hose clamp. Make sure to tighten the hose clamp. Start a program, watch the drainage-pipe their is no leak.

DOC Manager handels this. Happens rarely. Disconnect power(Fusebox). Open fronthatch where circuitboard is located.

Check all connections to curcuitboard. Make sure nothing has slipped out. Close hatch. Turn on fuse. See if machine works.

First do same steps as ''B1-Clocked water, can't be emptied''. If not the problem see step #2.

Open the hatch and look inside the machine. Furthest back and to the left of machine is a small grey ''pressure switch''(Measures water level)

Inspect if preassure switch is clogged with dirt, clean if so. IMPORTANT- Do not try to twist pressure switch, it will brake and cause leak.

Check under sink No3 that the balofix isn't closed. (pararell with pipe=open). See if machine can be emptied.

Drag out the machine very carfully. Use a flashlight to see the drainage-pipe.(Grey plastic pipe). Pull out the waterplug inside the machine.

Press the button on the controlpanel to empty the machine. See if there is any water leaking from the drainage-pipe.

Small holes or cracks in the drainage-pipe is the problem. Best solution- Change drainage-pipe(DOC)

Emerency solution- Small holes or cracks can be taped with waterproof tape. Should be changed at as soon as possible.

Drag out the machine very carefully. Take of the lid of the dishwasher. Unscrew the back of the machine.

Inspect the clear plasticpipe/backpipe for cracks. While looking at the backpipe, run a program. Water will be leaking very clearly if cracked.

If backpipe is cracked, DOC will change. Best if changed as fast as possible due to water will leak on electricity and cut power to bar.

Drag out the machine very carefully. Get behind the machine and inspect the small transparent pipe leading to detergent package under sink No3.

Check for cracks/holes. If leak is close to detergent package, cut of and place in package.

If leak is close to machine, change the pipe(DOC). DOC- Screw of backplate to machine. Find the entry to detergent on the back of the machine.

Change the whole pipe with new one. Pipe can be bought at any VVS store, just check size before buying.

Turn of fuse for machine.(IMPORTANT) Drag out the machine very carfully. Inspect power cable if bent or broken. Straighten the cable and turn on fuse.

If step #1 is not the problem their is a leak somewhere in the machine. Find leak and replace pipes. Machine needs to dry for a couple of hours.

If cable is broken it can be changed with a new one.(DOC). Most common problem is step #2.

Open the door to the cooler. Take out all products. Take out the shelfs in the cooler. Retreive a flashlight.

Use a flashlight and look behind the cooler if any ice is starting to build up. If so- Machine needs to be turned off during the night.

Make sure you open all doors and drawers to cooler. DO NOT store any products in the cooler during the night.

Person who opens the day after will turn on the cooler and see if temperature drops. Temperature should be right after 30-50 minutes.

Turn of the cooler. Clean the filter with a brush and/or with a compressor thoroughly. Turn on the cooler and wait for it do drop in temperature.

Check the fusebox that no fuse is off. Check the plug to the machine that it's correctly inserted. Change outlet for machine as well.

If step #1 won't work. -Change rockerswitch.(DOC) If machine still doesn't work go to step #3.

If the rockerswitch is not the problem change the powercord(DOC Difficulty 5/5). If machine still does not work-call service company.

Open up door to fridge. Inspect roof of fridge if ice is buidling up. If so, go to step #2.

Store all products inside the fridge and place in another fridge. Turn of the fridge and open the door.

Leave door open during the night. Opening juicer turn on the fridge and close door. Temperature should drop within an hour.

Clean filter above fridge with brush and/or compressor. See if temperature drops. If not- Contact DOC manager.

Take away all cardboard inside the fridge. Top shelf should be entirely clear of cardboard. See if temperature drops. If not - contact DOC manager.

Open the door and see if a lot of ice is starting to build up. Door might not be able to close due to ice build up.

Store all good in another freezer, turn of machine and leave door open over the night. Person who opens- clean freezer and wipe up all water.

Close the door and turn the machine back on. Temperature should be dropping within an hour. Contact DOC manager with results.

Unscrew the barfront opposite of the icemachine. Follow the grey drainage-pipe leading from machine to pump.

Inspect the pipe if twisted and/or are very long. Cut the pipe so it's as short as possible and still fits in pump.

Empty the icemachine by hand. DO NOT pull the plug inside the machine. This will break the pump.

Turn on machine when all of the water is out. Icemachine will need a day to fill with ice again. Inform DOC manager the day after.

Inspect the waterlevel inside the icemachine. Is water flowing through the steelpipe and spraying the roof with water.

If not- fill up the water level. Inspect the balofix located either at the faucet and/or under the sink.

Take away the front plate of the machine and inspect filter. Clean filter with brush and/or compressor.

The machine needs time to fill up. Inspect the machines ice level next day if it's properly filled.

Flip the grill upside down. Unscrew all screws holding the bottomplate together. Lift off the bottomplate exposing the inside of the machine.

Locate the On/Off switch. There are two wires connected to the switch. Loosen the screws and drag out the wires.

Make sure you remember where you took of the wires. Drag off the powerswitch exposing the two screws holding the switch at place.

Unscrew the screws and the switch will fall off. Replace the switch with a new one. Screw everything back together.

Unplugg the machine. Turn it upside down. Unscrew the screws holding the bottomplate in place.

Inspect the thermostat and On/Off switch if burned and in need of changing. If so- See video on how to.

Flip the grill upside down. Unscrew all screws locted att the bottom of the grill. Lift off the bottom.

Locate the rocker switch and unplug the four cableshoes attached to it. OBS- Make sure you remember where the cableshoes where sitting on the switch.

If any cable is burned- replace with new shoe. Use a flathead screwdriver to remove the old switch. Push the new switch in place.

Plugg the cable shoes back onto the switch the exact way it was before. If they are not placed the same way- fuse might go off.

While the bottom is off, locate the powercord. There are three cables that make the powercord.

Green/Yellow- Earth Blue- Neutral Black- Leading One. These has to be connected the same way you take them off.

Unscrew the three cables and pull the out of their socket. Drag the cord out of the machine. Take a new powercoard and bite of 1cm of the rubber.

Lead the new cord in to the machine and screw them in to the socket again. Earth to Earth Blue to Blue Black to Black.

Use an insect key/L key and locate the small screw. Tighten it properly with the insect key.

Unplugg the machine. Turn it upside down. Unscrew all screws holding the bottomplate together.

Inspect the thermostat if burned and/or if cables and cableshoes are burned. Change thermostat if so.(See video)

If thermostat is burned you should change cableshoes as well. If that does not work. Throw away the grill and order a new one.

Unplugg the machine. Turn the machine upside down. Unscrew all screws holding the bottom plate in place. Take away bottom plate.

Inspect the power cord if damaged or broken. If damaged or broken- see video how to change.

Find a flatheaded screwdriver (also used on the espresso machine showerhead), an 8mm spanner, or an adjustable spanner

Flip the centrifuge upside down. Locate the four nuts at the bottom of the machine. Unscrew the four nuts.

Carefully knock the bottom of the centrifuge loose and remove the bottom. Use a flat screwdriver to knock the bottom off.

Locate the screws holding the feet at place. Unscrew the screw with a star screwdriver and the foot will fall off.

Place the new foot on the correct position and place the screw in the hole inside the bottom of the machine. Screw it tightly.

Place the bottom back in it's place and attach the four nuts holding the bottom at place. Flip the centrifuge back to it's normal position.

Flip the centrifuge upside down. Unscrew the four nuts located at the bottom of the machine.

Use your screwdriver or any flathead tool to knock the yellow colored bottom off. This may be stuck so patience is needed. Do not use to much force.

Once bottom is of, carefully lift it up and let it hang to one of the sides. Make sure that no connection is being ripped off.

Locate the two metalpipes sitting on top of each other. You should see the two screws holding the pipes together. Unscrew the two screws.

Pull the handle all the way out. Take out the smaller pipe. Change the handle and repeat the steps to get it back together.

Try pulling the black handle off- is the matalpipe it's attached to following or is the metalpipe stuck. If metalpipe is stuck go to step #2.

Use an insect key to tighten the screw holding the handle in place with the metalpipe. If the metalpipe is loose go to step #3.

Metalpipe broken inside and needs to be changed. Call DOC manager and/or watch video. Use spare centrifuge in the mean time.

Make sure that the machines handle is properly closed. Try pressing the ''reset'' button located at the bottom of the centrifuge.

Hold the button in for 5sec then release. It will push itself out very slowly so won't start straight away. If it does not work- Contact DOC manager.